router help!

[angrypond]

hi, i dont know what the username or password for my router is, its a zyxel prestige 652h-31, ive tried all the defaults, admin, 1234 etc.. none have worked. I tried xscan i think i got the password through scanning snmp-info, it said "Found snmp-password: ******". Is there any way to detect the username, ive looked for a remote brute force username cracker but cant find one. i dont know much about this stuff just what ive learned myself.
thanks.

[TMG]

I didnt check out that site but ya, do a hard reset and it will revert to factory defaults.

[angrypond]

ok, its just last time i did that to fix a problem i didnt know the settings so we had to get someone round to fix it, is there anyway to get the configuration from the router.

[flashdude]

If you could log in to the router then alot of them have an option to save the settings and then after you hard restart it you can load the saved settings from file. What settings did you need someone else to set up for you? If its always on broadband cable then you just plug it in and go. If its dsl you just enter your isp's internet username and password (almost always different then email and password) If there are any other settings that you need to enter they would be provided from your ISP. static ip etc. Don't forget to change the default user name and password and set up the encryption for your wireless network.

[angrypond]

its always on, but i think its dsl because its 512k, and i cant get into the router, the engineer cahnged the username and pass i think.

[computerman]

reset the router. turn it around youll see a spot that says RESET and itll have a little hole, get a paper clip and press it for 5 seconds . you should know if you have dsl or cable

[angrypond]

yes but is there anyway to retrieve the configuration, before i do that, i got the password so is it possible to do that.

[angrypond]

last time i screwed it up.

[angrypond]

i found this using xscan, are these the configuration settings

[Snmp-Info]

Snmp-Password: ******

[Snmp-System-Info]:
sysDescr.0 = Prestige 652H/HW-31
sysUpTime.0 = 4 Days, 18 Hours, 18 Minutes, 30 Seconds
sysContact.0 =
sysName.0 = P652H-31
sysLocation.0 =
sysServices.0 = 14




[Snmp-Interfaces-Info]:
ifNumber.0 = 3

ifIndex.0 = 1
ifDescr.0 = enet0
ifType.0 = Ethernet Network
ifMtu.0 = 1500
ifSpeed.0 = 100000000
ifPhysicalAddress.0 =
ifAdminStatus.0 = Working normally
ifOperStatus.0 = Working normally
ifLastChange.0 = 500
ifInOctets.0 = 153659297
ifInUcastPkts.0 = 1006318
ifInNUcastPkts.0 = 19871
ifInDiscards.0 = 4941
ifInErrors.0 = 0
ifInUnknownProtos.0 = 4941
ifOutOctets.0 = 1322233823
ifOutUcastPkts.0 = 1363569
ifOutNUcastPkts.0 = 191
ifOutDiscards.0 = 0
ifOutErrors.0 = 0
ifOutQLen.0 = 0

ifIndex.1 = 2
ifDescr.1 = enet1
ifType.1 = Ethernet Network
ifMtu.1 = 1500
ifSpeed.1 = 10000000
ifPhysicalAddress.1 =
ifAdminStatus.1 = Working normally
ifOperStatus.1 = Idle
ifLastChange.1 = 0
ifInOctets.1 = 0
ifInUcastPkts.1 = 0
ifInNUcastPkts.1 = 0
ifInDiscards.1 = 0
ifInErrors.1 = 0
ifInUnknownProtos.1 = 4941
ifOutOctets.1 = 0
ifOutUcastPkts.1 = 0
ifOutNUcastPkts.1 = 0
ifOutDiscards.1 = 19871
ifOutErrors.1 = 0
ifOutQLen.1 = 0

ifIndex.2 = 3
ifDescr.2 = ppp
ifType.2 = Unknown
ifMtu.2 = 1526
ifSpeed.2 = 0
ifPhysicalAddress.2 =
ifAdminStatus.2 = Working normally
ifOperStatus.2 = Working normally
ifLastChange.2 = 3400
ifInOctets.2 = 1310998402
ifInUcastPkts.2 = 1419285
ifInNUcastPkts.2 = 0
ifInDiscards.2 = 0
ifInErrors.2 = 0
ifInUnknownProtos.2 = 0
ifOutOctets.2 = 139635866
ifOutUcastPkts.2 = 1032545
ifOutNUcastPkts.2 = 0
ifOutDiscards.2 = 3132
ifOutErrors.2 = 0
ifOutQLen.2 = 0





[Snmp-IP-Info]:
Address Net_Mask Bcast_Address Reasm_Max_Size
0.0.0.0 0.0.0.0 0 65535
86.133.15.224 255.255.255.255 1 65535
192.168.1.1 255.255.255.0 1 65535


[Snmp-TCP-Info]:
State Local Remote
LISTEN 0.0.0.0: 21 0.0.0.0: 0
LISTEN 0.0.0.0: 23 0.0.0.0: 0
LISTEN 0.0.0.0: 80 128.162.128.148: 0


[Snmp-UDP-Info]:
Address Port
0.0.0.0 161
0.0.0.0 1025
0.0.0.0 1900


[Snmp-Wins-Users]:




Plugin category: SNMP
Plugin name: Snmp-Info
Plugin author: glacier
Plugin version: 1.0
Risk rank: high
Description: "xfocus" vulnerability search engine "xfocus" exploit search engine

[d3fus3r]

use Look@Lan or Cain and Able cause with those two programs i can help you get the name back if you absolutely cant just reset this damn hting.

I mean just reset it and make a new pass and login name...it wont kill you...i dont see why you have to have these settings...

nvm i read that you said you screwed it up...still my point is that you have people who can help you here so listen to em or be left without a solution

[angrypond]

im not trying to critisize anyone or their knowledge, i just need to get into my router, basically i cant reset it because i don't know the configuration, last time i reset it, it screwed up and the isp would tell me the settings and i had to get an engineer round which cost a lot of money. therefore if i cant get the username and pass, (which isnt the default, i looked throught he manual, admin 1234) i thought if i could get the configuration i could then reset it and set it to what it was like before.

[TMG]

Theres not much we can do man, and its not hard to setup a router.

Who makes the router? What model?

You also should know if your DSL or Cable.

If your cable there is nothing for you to do, if your DSL all you have to do is enter the pppoe auth settings.

Is this a modem/router combo from your ISP? If it is there really isnt much we can do.

[angrypond]

zyxel 652h-31, ive been looking around my isp's site (BT) and my routers user guide and i think ive got some of the settings.
VPI number: 0
VCI number: 38
Authentication: CHAP
Modulation: G.DMT
Encapsulation: PPP over ATM (PPPoA)
Virtual Circuit Multiplexing (VC-MUX)
would, the pppoe authorization settings basically be an account username and password? if im making sense.

[TMG]

Right about the pppoe. So this is a business ADSL modem/switch then. Thats why you had to have a tech configure it.

[angrypond]

yep

[TMG]

Therefore we cant really help you. From the business DSL (covad) that I have used it needs to be configured provider side, not client side.