Whats your personal best?

[Maxvla]

P4 1.6a @ 2664 mhz with stock intel cooling.

66% overclock with no extra money spent. :cool:

hafta back it off a bit in order to run my memory at cas2 when running 3:4.

[Ender]

Right now I am at 1.61. My psu and ram are holding me back. Pc2100, and a 300watt antec psu. I haven't unlocked my cpu yet. Oh and it's an xp1700+. :D

[RangerJoe]

2016 mhz...(192x10.5) on my xp1600 with aircooling..sure it took 2vcore...but hey, temps never went over 45c...too bad my psu doesnt give enough power...it would get down to around 4.6v on the 5v line at full load..i dont want that....near 50% overclock isnt bad with air cooling...

[Ender]

Is that possible? Air cooling with a 2.0v core?

[Wicked Klown]

My best so far was done with my old 1.1 T-Bird(R.I.P.) I was able to push it to 1610 at 1.85 Vcore and a MC462 and 80mm 80CFM Delta.

[mdcomp]

What heatsink did you use RangerJoe? I got my XP 1600+ to 1876 on air cooling. I got the fsb to 190 and unlocked it.
:cool:

[Nickeleye]

My best is in my signature...

[JDXNC]

I'm running a K7S5A so i can only change my FSB but I run my 1600 at 1575Mhz with stock voltage 100% stable, I can post at 1743 (10.5 x 166)at stock voltage but it freezes just after the ram test.

[Anthony]

My best is 1671. My ram is a bottle neck right now, because I tried a friends corsair 2100 and I could go higher with it.

[R3nagad3]

JDXNC, what software or bios are you runnin' to set your FSB? I am using SetFSB 1.4a. Anyone got a newer version? The max I can get on my K7S5A is 146.6 FSB. I tried the bios at overclockers forum, but can't even get that high of an FSB. Oh well, time to change mobo's. Gonna look at the P4PE, heard it is pretty good.
Ren

[JDXNC]

I'm using the OC workbench Cheapo Bios at 150Mhz FSB, I tried SoftFSB but never got good results from it. What sort of PSU do you have? The K7S5A is a power hog and needs quite a bit of juice to OC well. I just got this 1600+ about 2 weeks ago, before that I had a 1Ghz Duron which ran for over a year at 1.24Ghz at 124MHz FSB.

[JDXNC]

Oh, and from what I see SoftFSB has been discontinued. The OC bios gave me much better results anyway. If you're getting a new mobo you should try the volt mod on your k7s5a.

[AstrumPreliator]

Man, I can see so many 120mm fans on these cpu heatsinks. I can already hear, or rather, not hear everything. My personal best is 1.5 on an xp1700+. But then again, I'm not really trying. :cool:.

[lunacy]

mine is a 667 Celery running at 900 MHz with aircooling. anything above that makes it think booting is a very bad idea. my average temperature is around 82°.

[smelanson]

I best one I ever got is my old 486 DX Overdrive 75 to run at 150MHz, the benchmarks say it is running at 190-200MHz but according to the multiplier and bus it should be 150MHz. I don't usually overclock my new chips but my P4 2.4GHz goes to 2.7 with stock cooling and no voltage change.

[JDXNC]

Here's the results from all my PC's.. and all of these are currently running these speeds 24/7! :

AMD Athlon XP 1600+ @ 1.57Ghz Stock voltage, 42C full load
AMD Duron 1Ghz @ 1.15Ghz (mobo max)
AMD K6-2+ 550 @600
AMD K6-2 450 @ 604!!! 2.5Vcore
P 200MMX @ 300
P 166MMX @ 200

[djinn1973]

My personal best to date is an (AMD) 1.133 @ 160 running a stable 1.800, all I used for cooling were seven 80.mm case fans. it was LOUD but it ran fantastic.

[SeanOMatic]

MP 1800+ @ 2 GHZ on a Vapochill.

[[GF]Burke]

hey JD, i use Cheepoman bios as well on my k7s5a. I can only get the fsb on my 1600 to 138/138 stable. i have done the chipset mod.. as well. she runs at 32c load~ air.

i had it at 150/150 but just had data coruption... :cry:

my Ti4600 is @ 335/730... HEHE

[cmelo9999]

I have an AOpen Geforce2 Mx 400. My card is running at 250/335 for a total of a 585Mhz RamDAC !!!! I needed some cooling, so i added a blue orb on the chip and the stock heatsink was mounted through the same holes but its on the back of the card i will post a pic soon.

[apexracer]

Dfi mobo for a 1.2ghz processor running a 500mhz celeron at 1023mhz.

[Evil_Spork]

check my sig... |/

600mhz on an AMD with air cooling. booya. :lol:

[brianmcenulty]

I've gotten my 1700+ tbred a (no b :() up to 2ghz (200x10) @ 1.9v. My ram (which is a one in a million kingston "value" stick lol) was sync at 200mhz and 2-2-2-5 @ 2.8v. Load temp: 37c. My ti4400 i got up to 320/735

[mentalcase]

Xp 2000+
1.82 with retail cooling

[caffeine4me]

I have a newertech g3 upgrade 4 my powermac 9500 and beat this: it overclocks automatically itself depending on the temp of my case. at 80 degrees f it runs at 272mhtz instead of 260mhtz check it out on the reveiws section of my site www.jtsmods.netfirms.com

[Conquistador]

I have a 450 MHz AMD K62, and it's running at 451 MHz... and i didn't do a thing!
________
Cheap Glass Bongs (http://glassbongs.org/)

[randy]

I got a Intel P4 3.06 running at approximately 3.47g. I hope to get it faster in the near future.

[Cross]

33mhz running at DOUBLE SPEED! 200% 66mhz, sadly the 33 is in shambles now

[ItsTooHot]

My best overclock was a PIV 1.8 @ 2790.

My current is a PIV 2.5 @ 3150

And I have a 2.66 that goes under the waterblock next week.

[bobthe pineapple]

OK, I've got a A7V333 ASUS motherboard, and a Athlon XP 2400+ proccessor. Does anbody have any experience with the same setup, any ideas what I should set my Frequency Multiplier to, and that other thing i forgot what it's called. (i.e.150x30) Plz help!? :)

[apeter]

1600+ @150Mhz FSB. turned comp on & and hour later it's at 30c 8) room temp about 68F.
edit: oh, yeah...that's air cooling 1571MHz

[Evil_Spork]

i had my old 1600+ @ 1701mhz @ 34* idel and 36* load.

[sixshot666]

Operating System: Microsoft Windows XP
Processor: XP 2000+ AMD Athlon™ o/c XP 2200+ @ 1.79
Graphics Card: NVIDIA GeForce4 Ti 4200 285/485
Total Physical Memory: 1 GB pc2100
Free Physical Memory: 706.18 MB
Motherboard Manufacturer: ECS
Motherboard Model: K7S5A
using HoneyX Bios stable at 143/143 with no motherboard mods

[razor02097]

so far... Pentium 150MHz overclocked to 266MHz

[ItsTooHot]

Well, I was disappointed with the new 2.66. It lives pretty happy at 3.2GHz, but I was really hoping for more.

[Evil_Spork]

ahh my current cpu is a 2100 tbred b and it hits 2517mhz on air at 2.2vcore @ about 41*c.. and thats stable. i like to keep it at about 2100-2200mhz on stock voltage for low temps.

[Edwards]

I'm still running my P4-1.8A at 2.7GHz (150FSB). It's using the stock intel cooler on an Asus P4B533 mobo. I can get win2k to boot at up to 155FSB, at 160, it either doesn't detect the HD, or BSODs. Too bad, it craps out at 2.9. 3.0GHz would be wonderful.

edit: I run F@H 24/7, I allow it to use 95% of my CPU, and at that 95%, it averages 46°C. At full load, 100%, it runs at around 50°C. Strange how that last 5% of CPU usage makes such a big difference.

the voltage is currently 1.575V. at 2.4GHz I only need 1.525V.

[apeter]

in my sig...highest supported fsb in this crap mobo...

[scottrempel]

Hi, I just joined the forum (my main forum www.nforcershq.com was down and I was bored). I watch TechTV all the time and really enjoy Yoshi's mods. Figured I would join the forum.

sig has the current OC....it's not bad I guess, but there is alot better. :D

[Evil_Spork]

new oc in sig.

once i get this POS mobo RMA'd for a new one ill be able to hit about 2.5 gig. my goal is an everyday use 100% OC.